Chat with us

Tag: tap water

  • Yellow Water and Black Particles From the Tap: What They Mean

    Yellow, brown or orange tap water is almost always iron or rust, from your own pipes, your geyser, the municipal main or iron-rich groundwater. Black particles are most often perished rubber from a washer or hose, sometimes carbon from a new filter or manganese in the supply. Both are usually a nuisance rather than an emergency, but a sudden change across your area, or a chemical or sewage smell, means stop drinking it and call your supplier.

    First, isolate the problem

    Before diagnosing anything, five questions narrow it down quickly. They take two minutes and tell you whether this is your plumbing, your building or the supply.

    1. Hot tap, cold tap, or both? Hot only points at the geyser or its inlet. Both points further upstream.
    2. One tap or all of them? One tap means that fitting or its supply line. All taps means the building or the main.
    3. Does it clear after running for two minutes? Clearing suggests water standing in pipework. Persisting suggests the incoming supply.
    4. Are the neighbours affected? If yes, it is the municipal supply and the supplier should be told.
    5. Did anything change recently? Mains work, a tanker delivery, a new filter cartridge, plumbing repairs, or the tank being cleaned.

    Note the answers before calling anyone. A plumber or a supplier can act on “cold tap only, all taps, clears after two minutes, started after mains work on Tuesday”. They can do very little with “the water looks funny”.

    Yellow, brown or orange water

    In the overwhelming majority of cases, this is iron. Where it comes from varies.

    PatternLikely sourceWhat to do
    Clears after a minute or two, worst in the morning Rust from your own galvanised iron pipework Flush before use. Replacing the pipe is the real fix
    Hot water only Geyser tank corroding, or a spent sacrificial anode Have the geyser serviced
    Sudden, all taps, neighbours too Municipal main, often after repair work or a pressure change disturbs deposits Report it. It usually clears within a day or two
    Persistent, does not clear Groundwater naturally high in iron Needs iron removal treatment ahead of any purifier
    Started after a tanker delivery Tanker water quality, or sediment stirred up in your tank Clean the tank and question the supplier

    BIS IS 10500 sets an acceptable limit of 0.3 mg/L for iron, largely because above that level water starts to taste metallic and stain. Iron at the levels that cause visible discolouration is generally an aesthetic problem rather than an acute health hazard, but it stains laundry and fittings permanently, and it is a reason to find out what is happening rather than to relax. If your home runs on a borewell or tanker, our guides to purifiers for borewell water and purifiers for tanker water go further.

    Black particles

    There are three common causes, and you can usually tell them apart by feel and by what changed recently.

    • Degraded rubber. Small, soft, rubbery flecks, usually from a perished washer, gasket or flexible connector hose. Harmless, but it means a component is failing and should be replaced. This is the most common answer by a wide margin.
    • Carbon fines. Fine black powder that appears shortly after a filter cartridge was changed. It is activated carbon dust from the new cartridge. Flush the system thoroughly and it should stop within a few uses.
    • Manganese. Black or dark brown staining and gritty particles from groundwater that contains manganese. It stains fixtures and laundry stubbornly and needs treatment rather than flushing.

    The quick test: rub a particle between your fingers. Soft and rubbery means a component. Gritty and persistent, especially with staining, is worth a water test. Our guide to testing water quality at home explains your options.

    Other colours and what they mean

    • Milky or cloudy, clearing from the bottom up: dissolved air, entirely harmless. If a glass clears from the bottom upward within a minute, that is air.
    • Cloudy and staying cloudy: suspended sediment. It needs filtration and a look at the tank.
    • Blue or blue-green staining: copper, usually from corroding copper pipework, and sometimes a sign of acidic water attacking the pipe.
    • Pink or reddish film in bathrooms: usually airborne bacteria growing on damp surfaces rather than anything in the water itself.
    • Green tint: algae, which points at a tank exposed to light. Cover the tank.

    When to stop drinking it

    Discolouration is usually a nuisance. Treat it as urgent, stop drinking it, use bottled water and contact your supplier if any of these apply:

    • It appeared suddenly across the whole area
    • There is an unusual smell, such as sewage, chemicals, fuel or solvent
    • There has been flooding, sewer work or a burst main nearby
    • People in the household have stomach upsets, vomiting or diarrhoea, in which case see a doctor as well
    • An advisory has been issued for your area

    Colour is a weak indicator of safety in both directions. Some genuinely dangerous contamination is invisible, and much visible discolouration is harmless. A sudden, widespread change is the signal that matters. For a fuller checklist, read is my tap water safe to drink?

    Before treating anything, find out what your area’s water typically contains. Look up TDS for your pincode in a few seconds.

    Check Your Water →

    What fixes what

    ProblemWhat actually deals with it
    Rust from your own pipes Replacing the pipework. Flushing is a workaround
    Rubber particles Replace the failing washer, gasket or hose
    Sediment from the tank Clean the tank, cover it, and clean it roughly twice a year
    Dissolved iron in the supply Dedicated iron removal before any purifier, because heavy iron fouls RO membranes fast
    Manganese Specific treatment. Get the water tested first
    Municipal disturbance Report it and wait. It usually resolves in a day or two

    One general point about purifiers here. An RO membrane removes dissolved iron well, and the sediment pre-filter catches visible particles. But a supply with a genuinely heavy iron or sediment load will clog pre-filters and foul membranes quickly. On such a supply, pre-treatment ahead of the purifier is not an upsell; it is what keeps the purifier working. Once the source is under control, a purifier such as Boon Homie, with two 5-micron sediment stages ahead of its RO membrane, handles the water you drink.

    Frequently Asked Questions

    Why is my tap water yellow or brown?

    Almost always because of iron or rust. It may come from corroding pipes inside your building, from the municipal main after a repair or pressure change, or from groundwater naturally high in iron. The quick test is whether it clears after running the tap for a few minutes, and whether it affects hot water, cold water or both.

    What are the black particles in my water?

    Most commonly they are small fragments of degraded rubber from a washer, gasket or flexible hose, which are harmless but mean the part should be replaced. Other possibilities are carbon fines from a recently changed filter cartridge, or manganese from the supply. If the particles are gritty rather than rubbery and keep appearing, have the water tested.

    Is yellow tap water safe to drink?

    Iron discolouration is generally an aesthetic problem rather than a health hazard at typical levels, but it is unwise to assume that about discoloured water. If the change is sudden, widespread in your area, or comes with an unusual smell, treat the water as unsafe until you know why, and contact your water supplier.

    Why is my water yellow only when I first turn the tap on?

    That points at your own plumbing rather than the supply. Water sitting overnight in corroding galvanised iron pipe picks up rust, which flushes out in the first minute or two. If it clears quickly and stays clear, the pipework is the source, and it will eventually need replacing.

    Can an RO purifier remove iron and rust from water?

    An RO membrane removes dissolved iron effectively, and visible rust particles should be caught by the sediment pre-filter before they reach the membrane. But heavy iron loads foul both quickly, so a supply with significant iron usually needs dedicated iron removal ahead of the purifier rather than relying on the purifier alone.

    Once the source is sorted, Boon Homie purifies your drinking water through two 5-micron sediment stages, carbon, RO and in-line UV, with WaterAI showing input and output TDS.

    See Boon Homie →
  • Chlorine in Tap Water in India: Is It Safe and Should You Remove It?

    Chlorine in Tap Water in India: Is It Safe and Should You Remove It?

    If your tap water sometimes smells faintly of a swimming pool, that is chlorine, and its presence is not an accident. Municipal water bodies add chlorine on purpose to keep water safe. Yet most people do not enjoy drinking it, and there are good reasons to remove the residual chlorine before it reaches your glass. This guide explains why chlorine is there, whether it is safe, and how to deal with it.

    Why There Is Chlorine in Your Tap Water

    Chlorine is the workhorse of municipal water treatment. It is added to kill bacteria and viruses at the treatment plant, and crucially it leaves a small residual amount in the water so that it stays disinfected on its long journey through pipes and tanks to your home. Without that residual, water could pick up contamination anywhere along the network.

    This is why the Bureau of Indian Standards recommends a minimum free residual chlorine of about 0.2 mg/L at the consumer end when water is chlorinated. In other words, a little chlorine in your tap water is a sign the system is doing its job.

    The takeaway: chlorine in tap water is intentional and protective. The small residual keeps water disinfected through the pipes. The reasons to remove it are taste, smell and disinfection byproducts, not acute danger from the chlorine itself.

    Is Chlorine in Tap Water Safe?

    At the controlled levels used in municipal supply, the chlorine residual is considered safe to drink, and the protection it provides against waterborne disease is significant. So the honest framing is that chlorine is a net positive in the supply network: the disease it prevents far outweighs the risk of the residual itself.

    That said, “safe to drink” is not the same as “pleasant to drink” or “ideal.” The taste and smell are off-putting, and there is a secondary concern about what chlorine can form when it reacts with organic matter, which is where most people decide to filter it out at the point of use.

    The Downsides: Taste, Smell and Byproducts

    There are two practical reasons to remove residual chlorine before drinking:

    • Taste and smell. The chlorine residual gives water a distinct pool-like odour and a flat, chemical taste that puts many people off drinking enough water at all.
    • Disinfection byproducts. When chlorine reacts with natural organic matter in water, it can form byproducts such as trihalomethanes. At the low levels of a well-managed supply these are generally considered low risk, but long-term exposure to higher levels is something water guidelines aim to limit, so reducing them is sensible.

    Both are addressed by the same simple technology: activated carbon, which adsorbs chlorine and its byproducts and restores a clean taste.

    Chlorine vs Groundwater Contaminants

    It is worth putting chlorine in context. Chlorine is mainly a municipal-supply issue: it appears in treated piped water. The contaminants that dominate India’s borewell and groundwater are different, things like fluoride, arsenic, nitrate and hardness, which chlorination does not address and which need reverse osmosis.

    Many Indian homes receive a mix of municipal and borewell water depending on the season and supply, so the ideal purifier handles both: carbon for chlorine and taste, and RO for the dissolved groundwater contaminants. To see what is actually in your supply, check the live, government-sourced reading for your area.

    Two Different Problems

    Chlorine is something the water authority adds to keep piped water safe. Fluoride, arsenic and nitrate are things nature or pollution put into groundwater. A good purifier removes the chlorine residual for taste and the dissolved contaminants for safety, in one system.

    Reference: BIS IS 10500 (free residual chlorine guidance); CGWB groundwater quality data

    How to Remove Chlorine from Drinking Water

    Removing chlorine is one of the easier water tasks:

    • Activated carbon filtration is the standard, effective method. Carbon adsorbs chlorine and byproducts and removes the taste and smell. It is a core stage in modern purifiers.
    • Letting water stand allows some chlorine to dissipate over time, but it is slow, inconsistent, and does nothing for byproducts or for groundwater contaminants.
    • Reverse osmosis purifiers include carbon stages before the membrane, partly to protect the membrane from chlorine, so they remove chlorine and taste while also removing dissolved contaminants. This is the most complete option.

    For most homes, a purifier that combines carbon stages with RO is the practical answer, because it solves the chlorine taste and the groundwater chemistry together. Our RO vs UV vs UF guide explains how the stages fit together.

    Want to know what is in your supply beyond chlorine? Check the live, government-sourced reading for your pincode.

    Check Your Water Quality →

    How Boon Handles Chlorine and More

    Boon is a water-technology company founded by ex-IIT Kanpur engineers and backed by the Technology Development Board (Government of India), NITI Aayog and Roca, with systems serving more than 4,000 organisations worldwide.

    8-Stage UltraOsmosis with Carbon Stages

    Boon’s 8-stage UltraOsmosis includes activated carbon stages that remove chlorine, its byproducts and the chemical taste, ahead of the RO membrane that removes dissolved groundwater contaminants. So whether your supply is chlorinated municipal water, borewell water or a mix, one system handles it and balances minerals back for a clean taste.

    WaterAI Monitoring

    The WaterAI app tracks input and output water quality and filter health in real time, so you know the carbon and membrane stages are working. WaterAI won the iF Design Award 2026.

    Free Professional Installation

    Boon’s technicians install the unit, measure your input water and verify output quality at no extra cost, so the purifier is matched to your real supply from day one.

    Clean-tasting, fully treated water: Boon’s 8-stage UltraOsmosis with carbon stages and RO, mineral balancing, WaterAI monitoring, and free professional installation.

    Explore Boon Tall →

    Frequently Asked Questions

    Is chlorine in tap water safe to drink in India?

    A small, controlled amount of chlorine is intentional and safe; municipal bodies add it to kill bacteria and viruses and to keep water disinfected through the pipes. The BIS standard recommends a minimum free residual chlorine of about 0.2 mg/L for this reason. The downsides are mainly taste and smell, and the disinfection byproducts that can form when chlorine reacts with organic matter. So chlorine itself is a safety feature, but most people prefer to remove the residual and its byproducts before drinking.

    Why does my tap water smell like chlorine?

    That swimming-pool smell is residual chlorine left in the water after municipal disinfection. It is a sign the water has been treated, which is good, but the taste and odour are unpleasant and put many people off tap water. The smell is usually harmless at normal municipal levels and is easily removed by an activated carbon filter, a standard stage in modern purifiers.

    What are disinfection byproducts and are they harmful?

    Disinfection byproducts, such as trihalomethanes, form when chlorine reacts with natural organic matter in water. At the low levels found in well-managed supplies they are generally considered low risk, but long-term exposure to higher levels is something water guidelines aim to limit. Activated carbon reduces chlorine and these byproducts, and reverse osmosis provides a further barrier, which is why a purifier with both is sensible for chlorinated water.

    How do I remove chlorine from drinking water?

    The simplest and most effective home method is an activated carbon filter, which adsorbs chlorine and improves taste and smell. Letting water stand allows some chlorine to dissipate but is slow, inconsistent and does nothing for byproducts. Modern purifiers include carbon stages, and an RO purifier adds a further barrier while removing dissolved contaminants, so a single purifier handles chlorine, its byproducts and the rest of your water quality.

    Does an RO purifier remove chlorine?

    Yes. RO purifiers include activated carbon stages that remove chlorine and improve taste before the water reaches the membrane, partly to protect the membrane itself. The combination of carbon filtration and the RO membrane removes residual chlorine and disinfection byproducts along with dissolved contaminants such as fluoride, arsenic, nitrate and hardness. Boon’s 8-stage UltraOsmosis includes carbon stages for exactly this purpose.

    Boon home purifiers: 8-stage UltraOsmosis with carbon stages and RO, mineral balancing, WaterAI monitoring, and free professional installation. Clean taste, fully treated water.

    Shop Boon Purifiers →