Chat with us

Tag: tds

  • Best Water for Tea and Coffee: Why Your Chai Tastes Different

    The best water for tea and coffee is clean, free of chlorine and other off-tastes, and moderate in minerals: not hard enough to leave a film on your chai, and not so stripped of minerals that the cup tastes flat. Water is most of what you drink in any cup, so when the same tea leaves or coffee powder taste different in another city, the water is usually the reason.

    Why water matters more than you think

    A cup of black tea or a tumbler of filter coffee decoction is almost entirely water. Even a milky masala chai is mostly water before the milk goes in. The tea leaves and coffee grounds give up their flavour into that water, and what is already dissolved in it changes how much comes out and how it tastes.

    Three things in your water do most of the work:

    • Hardness, mainly calcium and magnesium, often present as bicarbonates. These affect how tea compounds behave, how clear the cup looks and how quickly scale builds in a kettle.
    • Total dissolved solids (TDS), the overall mineral and salt content. Very high TDS can make water taste salty, brackish or bitter before you add anything to it.
    • Chlorine, added by many municipal supplies to keep water safe in the pipes. It has a sharp smell of its own and can flatten the aroma of a delicate tea.

    This is why your chai tastes one way at home in Chennai and another way at a relative’s house in Delhi, even with the same packet of tea. Cities draw water from rivers, lakes, borewells or tankers, treat it differently and deliver it through different pipes. The leaves are the same; the water is not.

    Hard water: scum, film and dull flavour

    If you have ever seen a thin, oily-looking skin on the surface of black tea, or a brown ring on the inside of the cup, you have seen hard water at work. Tea is rich in polyphenols, the compounds that give it colour, body and astringency. In hard water, especially water high in calcium bicarbonate, these compounds react with the minerals and with air to form a film that floats on the surface and sticks to the cup.

    Hard water tends to make tea:

    • Darker and cloudier, because the alkaline bicarbonates shift the colour of tea compounds.
    • Duller in flavour, with less of the bright, brisk edge that good leaves can give.
    • Harder to clean up after, with stains on cups and scale in the kettle.

    Milk and sugar hide a lot of this in a strong masala chai, which is one reason Indian households often do not notice it until they try a plain black or green tea. The same film can show up in filter coffee as a dull, flat finish. If you see white crust on your taps and in your kettle, our guide to white residue on taps and hard water explains what it is, and hard water vs soft water covers the difference in detail.

    Very high TDS and chlorine

    Very high TDS. Borewell and tanker water in many parts of India carries a lot of dissolved salts. You can often taste it in plain water: salty, brackish or slightly bitter. Boiling does not remove dissolved salts; as some water evaporates, they become slightly more concentrated. That taste carries straight into tea and coffee, and spices in a masala chai only partly cover it. BIS IS 10500 sets 500 mg/L as the acceptable TDS limit for drinking water, and supplies well above that are common on borewells.

    Chlorine. Municipal water is often chlorinated, and that is a good thing for safety in the pipes. But chlorine has its own smell, and it can react with the aromatic compounds in tea and coffee, so the cup smells less of tea and more of a swimming pool. Some free chlorine escapes as water is boiled, but not all disinfectants used in city supplies behave the same way, and the taste can linger. If your water tastes salty, metallic or of chlorine before it ever meets a tea leaf, start with our guide to why water tastes salty, metallic or of chlorine.

    Very low TDS: when water is too plain

    It is tempting to think the purest water makes the cleanest cup. In practice, water with almost no minerals can disappoint too. Many people describe very low-TDS water as tasting flat or empty, and tea and coffee brewed with it can taste thin, sharp or lacking in body.

    Part of this is chemistry. Minerals in water, magnesium and calcium in particular, interact with the flavour compounds in coffee and tea and influence how they are drawn out. Water with almost nothing dissolved in it extracts differently, and the result can be a cup that is technically clean but less rounded. Coffee brewers have long talked about water needing “some” minerals for good extraction, not none and not a lot.

    This is why RO water, which removes most dissolved solids, sometimes gets blamed for flat tea. It is safe to drink; it is simply very plain. Our explainer on why RO water tastes flat covers the reasons and the fixes.

    Tea and coffee by water type

    Water typeWhat you may notice in teaWhat you may notice in coffeeWhat helps
    Hard water (high calcium and magnesium)Surface film, brown rings, darker and duller cupFlat finish, scale in the filter and kettlePurification that reduces hardness; regular descaling
    Very high TDS (salty borewell or tanker)Salty or bitter undertone that spices only partly hideHarsh, muddy tasteRO purification rated for your input TDS
    Chlorinated city waterWeaker aroma, chemical smellAroma dulled, sharp noteActivated carbon filtration
    Very low TDS (heavily stripped water)Thin, sharp or flat cupCan taste sour or hollowWater with a moderate mineral profile
    Clean, moderate-mineral waterClear cup, true to the leafRounder, more balancedKeep it fresh and do not reboil repeatedly

    There is no single perfect number. Taste is personal, and a strong ginger chai is far more forgiving than a delicate first flush or a carefully measured pour-over. Treat the table as a guide to what to look for, then trust your own cup.

    Your cup starts with your tap. Look up typical TDS for your pincode to see whether hardness or high TDS is likely behind the taste.

    Check Your Water →

    Scale in kettles and coffee filters

    When hard water is heated, dissolved calcium bicarbonate turns into calcium carbonate, which does not stay dissolved. It settles as white or cream-coloured scale on the element of an electric kettle, the bottom of a saucepan and the holes of a steel filter coffee maker.

    • It changes the taste. Flakes of scale end up in the cup and the kettle itself starts to smell stale.
    • It slows things down. Scale insulates a kettle element, so water takes longer to boil, and it can clog the fine holes of a coffee filter so the decoction drips slowly.
    • It is easy to remove. A soak in diluted white vinegar or a citric acid solution, followed by a thorough rinse with clean water, loosens most scale. Do it regularly in hard-water cities.

    If scale returns within days of cleaning, your water is hard, and descaling only treats the symptom. Reducing the hardness of the water you brew with is the lasting fix.

    Practical tips for a better cup

    1. Start with fresh water. Water that has been boiled again and again loses dissolved air and concentrates its minerals. Fill the kettle fresh for each brew.
    2. Know your water. Check the TDS at your tap with a meter, or look up typical levels for your area. It tells you whether you are dealing with hardness, high TDS or neither.
    3. Run a side-by-side test. Brew the same tea with your tap water, your purified water and a bottle of packaged water. The differences are often obvious.
    4. Deal with chlorine. Activated carbon filtration removes chlorine taste. Leaving a jug of water open for a while can also let some escape.
    5. Avoid extremes. If your purified water tastes thin in tea, look for a purifier that lets you add back some minerals rather than going back to hard tap water.
    6. Descale on a schedule. Kettles, saucepans and coffee filters all need it in hard-water homes.

    Where Boon Homie fits

    Boon is a water-technology company founded in 2013 by ex-IIT Kanpur engineers, backed by the Technology Development Board (Govt. of India), NITI Aayog and Roca, with systems running in 4,000+ organisations and 400+ hotels across nine countries. Boon Homie, our wall-mounted RO purifier, is built around the idea that water for drinking and water for brewing do not have to be the same.

    Homie purifies first: sediment pre-filtration, carbon for chlorine and chemical taste, an RO membrane rated for input up to 2000 TDS, and in-line LED UV before the tank. Then three Water Profile buttons let you choose what comes out. Bev is water meant for brewing coffee and tea, one press, no app needed. Daily is balanced water for drinking and cooking, and Active is for after exercise and mornings. Mineral Enhancers, each on its own cartridge separate from the main filter, shape the mineral profile and taste. Homie is ₹21,900 at the time of writing, with free installation by Boon’s own team and a 2-year warranty.

    Where it does not fit: a purifier will not make poor leaves taste good, and taste in the cup is personal, so try your favourite tea and decide. If your supply is above 2000 TDS, Homie’s membrane is not rated for it.

    Frequently Asked Questions

    What is the best water for making tea?

    Clean water with no chlorine taste and a moderate mineral content usually gives the clearest, truest cup. Very hard water tends to leave a film and dull the flavour, very high TDS adds a salty or bitter note, and water with almost no minerals can taste thin. Use fresh water each time and try a side-by-side test to find what you prefer.

    Why does my tea have a film or scum on top?

    That film usually comes from hard water. Tea polyphenols react with calcium and bicarbonate in the water, and with air, to form a thin skin on the surface and brown rings on the cup. It is not harmful, but it makes tea look cloudy and taste duller. Water with lower hardness reduces it, and it is most visible in black tea without milk.

    Why does chai taste different in another city?

    Because the water is different. Cities draw water from rivers, lakes, borewells or tankers, treat it in different ways and carry it through different pipes. Hardness, TDS and chlorine all change how tea leaves release their flavour and how the cup tastes, so the same packet of tea can taste brighter in one city and duller or saltier in another.

    Is RO water good for tea and coffee?

    RO water is clean and free of the hardness and salts that cause film and bitterness, which helps on hard or high-TDS supplies. On its own it is very low in minerals, so some people find tea and coffee brewed with it taste thin or flat. A purifier that adds back a moderate mineral profile after RO is one way to get a rounder cup.

    Does boiling water improve it for tea?

    Boiling kills microbes and lets some free chlorine escape, but it does not remove dissolved salts or most hardness. As water evaporates, TDS actually rises slightly, and heating hard water forms scale in the kettle. Reboiling the same water repeatedly makes this worse, so fill the kettle with fresh water each time you brew.

    How do I remove scale from my kettle?

    Soak or boil the kettle with a solution of diluted white vinegar or citric acid, leave it for a while, then scrub lightly and rinse thoroughly with clean water before using it again. Steel coffee filters can be soaked the same way. If scale returns within days, your water is hard, and reducing its hardness is the lasting fix.

    Homie’s Bev profile gives you water meant for brewing coffee and tea, one press, after full RO purification. Brew your usual cup and taste the difference yourself.

    See Boon Homie →
  • Do You Need a Water Purifier? An Honest Decision Guide for Indian Homes

    Most Indian homes need some form of water treatment, but not always an RO purifier. If your water is low-TDS municipal supply, UV or UF (or boiling) handles the main risk, which is microbes. If it is high-TDS, borewell or tanker water, or a test shows fluoride, arsenic or nitrate above the limits, you need RO. Test before you buy.

    The Short Answer by Situation

    Your situationWhat you likely need
    Municipal water, TDS under about 200, tastes fineUV or UF purifier, or boiling; RO is usually overkill
    Municipal water, TDS about 200 to 500UV or UF is often enough; RO is optional, mainly for taste
    TDS above 500, any sourceRO rated for your input TDS, with UV or UF
    Borewell waterA lab test first; usually RO
    Tanker waterRO with UV, because quality changes load to load
    Test shows fluoride, arsenic or nitrate above limitsRO, regardless of TDS

    Step 1: Test Your TDS

    TDS (total dissolved solids) is the single most useful first number, because it tells you whether RO is even on the table. Start by looking up the typical reading for your pincode, then confirm it with a handheld TDS meter at your own tap. Readings in one building can differ between municipal, borewell and tanker supply.

    A TDS meter does not tell you about microbes, fluoride or arsenic. For borewell water, or if anything about your water seems off, get a lab test. Our guide on how to test water quality at home covers meters, kits and when a lab is worth it.

    Start with your number. Look up typical TDS for your pincode, then confirm it with a meter at your own tap.

    Check Your Water →

    Step 2: Know Your Source

    • Municipal (piped) water is treated and usually chlorinated at the plant. TDS is often low to moderate. The main risk is contamination on the way to you: leaking lines, intermittent supply and dirty storage tanks. That is a microbial risk, which UV or UF addresses.
    • Borewell water is untreated groundwater. It can be high in TDS and hardness, and in some regions carries fluoride, arsenic, nitrate or iron. It also changes with the seasons. This is where RO is most often justified.
    • Tanker water may come from different sources on different days, so you have to plan for the worst load, not the best. RO with UV is the safe default.

    Step 3: Compare Against BIS Limits

    India’s drinking water standard, BIS IS 10500, gives you the numbers to compare a test against:

    ParameterBIS IS 10500 limitTreatment if exceeded
    TDS500 mg/L acceptable; 2000 mg/L permissible where no alternativeRO
    Total hardness200 mg/LRO for drinking; softener for the house
    Fluoride1.0 mg/LRO
    Arsenic0.01 mg/LRO
    Nitrate45 mg/LRO
    Iron0.3 mg/LIron removal pre-filter, then purifier

    If everything is within limits and the source is municipal, your job is mainly to make water microbially safe. That is a cheaper, simpler problem than the one RO solves.

    Which Type of Purifier, If Any

    • UV: inactivates bacteria and viruses. Needs clear water and electricity. Does not change TDS or remove particles.
    • UF: a membrane that physically blocks bacteria, cysts and particles. Works without electricity in many designs. Does not reduce TDS.
    • RO: reduces dissolved salts, hardness, fluoride, arsenic and nitrate. Needs power and sends some water to the drain. Usually paired with UV or UF.
    • Boiling: a reliable stopgap for microbes, and useful during an outbreak or when travelling. It does not remove dissolved salts or chemicals, and as some water evaporates, those slightly concentrate. Our comparison of boiling water vs an RO purifier covers when each makes sense.

    So “which type is best” has no single answer. The right type is the one that treats what your water actually contains.

    Do Water Purifiers Really Work?

    Yes, for what they are designed to remove, and only while they are maintained. RO does reduce dissolved salts; UV does inactivate microbes in clear water; UF does block bacteria and particles. Where they fail is mismatch and neglect: a UV purifier on high-TDS borewell water leaves the salts untouched, and a purifier running on overdue filters or a failing UV lamp gives a false sense of safety. Check output TDS now and then with a meter, and service on time.

    If you have stomach upsets, diarrhoea or other illness that you suspect is linked to water, see a doctor. A purifier is a prevention tool, not a treatment.

    Why Salesmen Push RO on Soft Water

    It is a fair question. RO units cost more and need more parts replaced over time, so they are worth more to whoever sells and services them. Demonstrations add to the pressure: a TDS meter showing a lower number after RO looks convincing, and colour-changing electrolysis demos show dissolved minerals, not whether water is safe. Lower TDS is not the goal in itself. On soft, low-TDS municipal water, RO removes little that needs removing, wastes some water to the drain, and can leave water tasting flat. Our guide on whether you need RO if your TDS is below 200 sets out that case.

    That applies to Boon too. For low-TDS supplies, Boon Tap UF, which has no RO, exists for exactly that situation. For high-TDS, borewell or tanker water, Boon Homie (₹21,900 at the time of writing) and Boon Tap (from ₹23,500) are RO purifiers rated for input up to 2000 TDS, with WaterAI monitoring of input and output TDS and filter health, installed free by Boon’s own team.

    Frequently Asked Questions

    Do I need a water purifier if I get municipal water?

    Usually some treatment, but often not RO. Municipal water is treated at the plant, but it can pick up microbes from leaking lines and storage tanks on the way to you. If your TDS is low and a test shows nothing else above BIS limits, a UV or UF purifier, or boiling, handles the main risk. RO is needed mainly when TDS is high.

    Do water purifiers really work?

    Yes, for what each technology is designed to remove, as long as it is maintained. RO reduces dissolved salts, fluoride, arsenic and nitrate. UV inactivates bacteria and viruses in clear water. UF blocks bacteria, cysts and particles. Purifiers fail when they are mismatched to the water or run on overdue filters, so test your water and service on time.

    What type of water purifier is best for my home?

    The one that matches your water. For low-TDS municipal water, UV or UF is usually enough. For TDS above 500, borewell or tanker water, or any test showing fluoride, arsenic or nitrate above BIS limits, choose RO rated for your input TDS, paired with UV or UF. Test your TDS and know your source before choosing.

    Why do salesmen push RO purifiers even when municipal water is soft?

    RO purifiers cost more and need more replacement parts over time, so they are worth more to the seller. TDS meter and electrolysis demonstrations make lower TDS look like safer water, which it is not by itself. On soft, low-TDS municipal water, RO removes little that needs removing, wastes some water and can make water taste flat.

    Is boiling water enough instead of a purifier?

    Boiling reliably kills microbes, so it is a good stopgap for low-TDS municipal water, during an outbreak or while travelling. It does not remove dissolved salts, fluoride, arsenic, nitrate or other chemicals, and slightly concentrates them as water evaporates. For high-TDS or borewell water, boiling is not a substitute for an RO purifier.

    How do I know if my water needs RO?

    Measure your TDS with a meter and compare it to the BIS IS 10500 acceptable limit of 500 mg/L. If it is above that, or your water is from a borewell or tanker, or a lab test shows fluoride above 1.0 mg/L, arsenic above 0.01 mg/L or nitrate above 45 mg/L, you need RO. Below about 200 with nothing else, you usually do not.

    If your test shows high TDS or borewell water, Boon Homie is a wall-mounted RO with UV and live input and output TDS monitoring, ₹21,900 at the time of writing.

    See Boon Homie →
  • Water Purifier Without Electricity: What Actually Works in a Power Cut

    No RO purifier works without electricity: reverse osmosis needs a pump to push water through the membrane, and UV needs power too. Non-electric gravity purifiers can remove sediment and deal with microbes, but they cannot reduce TDS. So the right plan for power cuts depends on your water: on a high-TDS supply, keep purified water stored and plan a backup; on a low-TDS supply, a gravity purifier can be a reasonable fallback.

    Why RO needs electricity

    Reverse osmosis works by forcing water through a membrane with pores so fine that most dissolved salts cannot pass. Water naturally wants to move the other way, from the purer side to the saltier side, so the system has to apply pressure to overcome that. The saltier your water, the more pressure it takes.

    Most Indian homes get water from an overhead tank by gravity, at a pressure far too low for this. That is why a home RO purifier has a booster pump, and the pump runs on electricity. The UV stage needs power for its lamp or LEDs, and most purifiers also use electric valves and sensors. Without power, the purification stops.

    That is not a design shortcut any brand can avoid. If a product claims to reduce TDS like RO without electricity and without a pressurised supply, ask how.

    What non-electric purifiers can and cannot do

    “Non-electric” purifiers work by gravity: you pour water into an upper chamber and it trickles through filters into a lower one. Depending on the model, the stages can include:

    • Sediment filters to take out dust, rust and visible particles.
    • Activated carbon to improve taste and reduce chlorine and some chemicals.
    • An ultrafiltration (UF) membrane, fine enough to hold back bacteria and cysts without pressure.
    • Chemical disinfection, where a cartridge releases a disinfectant to deal with microbes.

    What none of these can do is reduce dissolved salts. TDS in, TDS out. If your supply is high in TDS or has dissolved contaminants such as fluoride or nitrate, a gravity purifier will not bring them down. Our comparison of UF, NF and RO purifiers explains why.

    On a supply that is already low in TDS, such as treated municipal water in many cities, a gravity purifier can be a perfectly sensible primary or backup option. Our guide on whether you need RO if your TDS is below 200 helps you decide.

    Boiling during a power cut

    Boiling is the traditional answer and it does one job well: a rolling boil kills bacteria, viruses and parasites. But it needs gas or another fuel, it is slow for a family’s daily water, and it does nothing for TDS. Boiling actually concentrates dissolved salts slightly, because some water evaporates and the salts stay behind. It also does not remove fluoride, arsenic or nitrate.

    If you boil, let the water cool covered and store it in a clean, covered container. For the full comparison, see boiling water vs an RO purifier.

    Every option compared

    OptionReduces TDS?Deals with microbes?Needs power?Best used for
    RO + UV purifierYesYesYes, to purifyEveryday purification, especially on high-TDS supplies
    Purified water stored in advanceAlready reducedAlready treated; keep it clean and coveredNot to store; depends on how you dispense itShort and scheduled cuts
    Inverter or UPS backup for the ROYesYesYes, from the batteryFrequent or long cuts
    Gravity purifier (UF or chemical)NoYes, within its design limitsNoLow-TDS supplies
    BoilingNo (slightly concentrates)YesNeeds fuel, not electricityEmergency backup

    There is no option that reduces TDS without power. On a high-TDS supply, the real answer to power cuts is to have purified water already in storage, and a way to get it out.

    A practical power-cut plan

    1. Know your TDS. Everything else follows from this. Check typical TDS for your area, then confirm with a meter at your own tap.
    2. On a low-TDS supply (comfortably within the BIS IS 10500 acceptable limit of 500 mg/L), a gravity purifier is a reasonable backup for microbes during long outages.
    3. On a high-TDS supply, treat stored purified water as your buffer. Keep the purifier’s tank full ahead of scheduled cuts, and fill a few clean steel or glass containers if outages run long.
    4. If cuts are frequent, ask an electrician whether your inverter can include the purifier’s socket, and check the purifier’s rating against your inverter’s spare capacity.
    5. Keep boiling as the last resort for microbes, accepting that it does not fix TDS.
    6. Remember the building pump. If your society’s pump also stops during a cut, the overhead tank may run low, so stored water matters even more.

    Your plan starts with your TDS. Look up typical TDS for your pincode before choosing between RO and a gravity purifier.

    Check Your Water →

    The overlooked problem: getting stored water out

    People often assume that if a purifier has litres of clean water in its tank, they can use it during a power cut. With some purifiers that is true: water flows out of a simple tap by gravity. With others, dispensing depends on an electric button, valve or pump, so the stored water stays locked inside until the power returns.

    Before you buy, ask a direct question: “How do I get water out of the tank when the power is off?” The answer matters as much as the storage size.

    Where Boon Homie fits, and where it does not

    Boon was founded in 2013 by ex-IIT Kanpur engineers, is backed by the Technology Development Board (Govt. of India), NITI Aayog and Roca, and runs water systems in more than 4,000 organisations. Boon Homie is our wall-mounted RO purifier, and it is built for exactly this gap.

    Homie has patented manual filling: during a power cut you can draw water by hand from its 8-litre tank. That water has already been purified. Purification itself still needs power, so Homie is not a non-electric purifier; once the tank is empty, you wait for power to return. When the power is on, it purifies at 20 litres per hour through five stages, including an RO membrane rated for input up to 2000 TDS and in-line LED UV before the tank. WaterAI monitoring shows input and output TDS so you know what you are drinking.

    Homie is ₹21,900 at the time of writing, on pre-order with deliveries from 15 October 2026, with free installation by Boon’s own team and a 2-year warranty.

    Where it does not fit: if you want a purifier that runs entirely without electricity, Homie is not one, and on a low-TDS supply a gravity purifier may serve you better. If your outages last a full day or more, 8 litres will not cover a family, so you still need stored containers or inverter backup. And if your supply is above 2000 TDS, its membrane is not rated for it.

    Frequently Asked Questions

    Can an RO purifier work without electricity?

    No. Reverse osmosis needs pressure to push water through the membrane, and in most Indian homes that pressure comes from an electric booster pump. UV stages need power too. During a power cut an RO purifier cannot purify, though depending on its design you may still be able to draw water already stored in its tank.

    Do non-electric water purifiers reduce TDS?

    No. Gravity purifiers use sediment filters, carbon, ultrafiltration membranes or chemical disinfection. These can remove particles and deal with microbes within their design limits, but none of them reduce dissolved salts. If your supply is high in TDS or contains fluoride, arsenic or nitrate, a non-electric purifier will not bring those down.

    Is a gravity purifier enough for my home?

    It can be if your supply is already low in TDS and your main concern is microbes, as with treated municipal water in many cities. Check your TDS first. If it is comfortably within the BIS IS 10500 acceptable limit of 500 mg/L, a gravity purifier is reasonable. If it is higher, you need RO, with stored water for power cuts.

    Does boiling water reduce TDS?

    No. Boiling kills bacteria, viruses and parasites, but dissolved salts stay in the water. As some water evaporates, TDS actually rises slightly. Boiling also does not remove fluoride, arsenic or nitrate. It is a useful emergency backup for microbes during long power cuts, but it is not a substitute for RO on a high-TDS supply.

    Can I run my RO purifier on an inverter?

    Often, yes, if the purifier’s socket is on the inverter circuit and the inverter has spare capacity. Ask an electrician to check your inverter’s rating against the purifier’s power requirement before relying on it. If cuts are frequent and long, inverter backup lets the purifier keep working rather than just dispensing stored water.

    How does Boon Homie work in a power cut?

    Boon Homie has patented manual filling, which lets you draw water by hand from its 8-litre tank during a power cut. That water has already been purified. Purification itself needs electricity, so once the tank is empty you wait for power to return or use stored containers. Homie is not a non-electric purifier.

    Homie lets you draw already-purified water by hand from its 8-litre tank when the power goes. Pre-order now, deliveries from 15 October 2026.

    See Boon Homie →